• Q1: RTSP rule of sunell IPC2021-09-01
  • RTSP rule : rtsp://ip:port/snl/live/cameraid/streamid

    IP : the IPC's IP address

    port: default port for RTSP is 554

    snl:sunell

    cameraid:default value is 1

    streamid: stream id, default value is 1


    For example : rtsp://192.168.0.120:554/snl/live/1/1

  • Q2: Why can't video be stored in SD card2021-08-13
  • Possible reason below:

    1. video configuration issue

       go to configuration->device record->record policy   , check whether the parameters are correct.

    2.SD card issue

    It may be due to SD card failure or SD not inserted into the card slot. Power off and re insert the SD card or replace the SD card

    3.other

    It may be caused by other non-human factors. Please contact the manufacturer in time

  • Q3: How many preset points could be added to one tour ?2020-11-16
  • In the tour setting of PTZ, you can add 256preset points into one tour at most.

  • Q4: How to set PTZ tour on the web?2020-11-16
  • 1. open PTZ control panel

    2. Select an area with the mouse ,and Set preset ID:1 Name: area1, then click "+"

    3. Select an area with the mouse again ,and Set preset ID:2 Name: area2 ,then click"+"

    4. go to "Tour", here show you how to add two preset points "area1 and area 2" to a tour:

    1) select tour ID ,default is 1,  tour name : enter a name

    2)click  to start

    3)select "Preset”=area1, enter 5(sec) to "Wait Time", click ""

    4)select "Preset”=area2, enter 5(sec) to "Wait Time", click ""

    note : you can add more preset points as you want.

    5)click  to end

    6) then you can click  to check your setting for [Tour1]

  • Q5: How to see Video Stream Draw Line2020-11-16
  • 1. For example , Open "Video Stream Draw Line" in Intelligent Analysis

    2. set the related area

    3.  in the "Live Video" interface, select "stream2" in the Stream option. then you can see the Line

  • Q6: How to enable function of pushing alarm info. to app on the IPC?2020-11-16
  • 1. Login the IPC

    2. Go to push Message->Configuration

    3. Enable the option "Push Message"

  • Q7: 802.1X2020-11-16
  • IEEE 802.1X is a standard to authenticate network clients (or ports) according to user ID or device. This process is called "port-level authentication". It uses RADIUS (Remote Authentication Dial-up User Service) method and divides it into three different groups: requester, authenticator and authorized server.

    The 802.1X standard applies to terminal devices and users (requesters) attempting to connect to ports or other devices, such as Cisco Catalyst switches or Cisco Aironet series access points (authenticators). Authentication and authorization are implemented through back-end communication of authentication servers such as Cisco Secure ACS. IEEE 802.1X provides automatic user identification, centralized authentication, key management and LAN connection configuration. The whole 802.1x implementation design consists of three parts: requester system, authentication system and authentication server system.

    In our IPC, you can see the setting: Network Service->802.1X

  • Q8: How to check when you failed to open the IPC's webpage?2020-11-16
  • 1. Check the IP is correct or not, use our ip search tool to find it.

    2. Check the port is correct or not, our default port is 80, if the manager changed it , it may not be the default value. (default typing 192.168.0.120:80)

    3. Check the "http" protocol has been changed to https, then you need to type https://192.168.0.120, but not http://192.168.0.120

    4. Make sure the password is correct. The default account infor. is  admin/admin

    5. Make sure the network port hardware is working fine. it will flicker all the time. 

  • Q9: What's the meaning of Control Port, HTTP Port and RTSP Port?2020-11-16
  • 1. In our IPC setting, you can see these these ports:

    2. Explaination

    Control Port: It is used for data transmission and the sunell's private connection protocol.

    Http     Port:  It is used for accessing our IPCs via web interface. For example, type “http://192.168.0.120:80" to access one IPC .

    RTSP    Port:  It is used for obtaining the video and audio stream resources. from the IPC.

  • Q10: How to open the HTTPS on the IPC?2020-11-16
  • 1. Login the IPC

    2. go to "Configuration"->"Device"->"System"->"Web Mode"

    3. select HTTPS and click "" to confirm it

    4. the IPC will restart

    5. Then the new access address is : https://192.168.0.120 (for example)

  • Q11: How to view the live stream of the devices on VLC Media Player?2020-11-16
  • 1. Download a VLC video player from the App Store. Please note that the supported version is 2.2.6 or higher.


    2. On VLC, click Media > Open Network Stream or Ctrl+N.

    3. Go to Network tab and input the URL.

    For IP Camera:

    · URL Formatrtsp://

    · Device IP: replace with the actual IP address of the device. Example: 192.168.0.120

    · Stream ID: replace with 1, 2 or 3.

    For NVR:

    · URL Formatrtsp://

    · Device IP: replace with the actual IP address of the device. Example: 192.168.0.121

    · Channel ID: replace with the exact channel, for 4ch NVR, it can be 1, 2, 3 or 4.

    · Stream ID: replace with 1, 2 or 3.

    For DVR:

    · URL Formatrtsp://

    · Device IP: replace with the actual IP address of the device. Example: 192.168.0.121

    · Channel ID: replace with the exact channel, for 4ch DVR, it can be 1, 2, 3 or 4.

    Note: 554 and 3036 are the default values of device. If you changed the port number 554 for IPC and NVR or 3036 for DVR, you should use the number you changed it to.


    4. Enter the device’s username and password if the dialog box below pops up.


  • Q12: What can I do if my device got bricked?2020-11-16
  • 1. On your computer, open the IP Search Tool. Checked if the tool can still find the device.

    If the tool can still find the IP address of the device, proceed with updating the firmware.


    2.  If the IP Search Tool cannot find the IP address of the device, but you still remember the IP address of the device, try to ping the specific IP address. If IP address can still be pinged, proceed with updating the firmware.


    3. If the device cannot be detected by the IP Search Tool and you don’t remember the IP address of the device, please try to ping the temporary IP address as listed below. 

       · IP Camera – 192.168.0.120

       · NVR – 192.168.0.121


    4. If the IP address can still be pinged, proceed with updating the firmware.


    Notes:

    1. Please ensure that the computer has the same IP range as the IP addresses listed above. For example, before you ping 192.168.0.120, set the computer’s IP address to 192.168.0.x

    2. It is highly recommended to connect the device directly to the computer to avoid any IP conflict.

    3. After pinging timeout and the device can be pinged again, immediately click ‘Add’ and then ‘Update’ on the Update Tool. Please ensure to uncheck ‘add online device’.

1 2 3 4 5

A total of 5pages

Get in on the latest news & products information.
Sign up to be the first to receive the Latest news & products information. You can unsubscribe with one click at any time, but we think you won’t want to.

click here to leave a message

Leave a Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

products

about

Contact